Are you looking for a way how to put a lace front wig on? In this article, you will learn how to put lace front wig on easily and quickly!

1. First, flatten your hair and prep your skin.

2. Next, make adjustments to the wig, such as tightening the straps and cutting the lace.

3. Finally, apply adhesive or wig tape and pull back.

Once this one is perfectly arranged, you can style it however you want!

Getting ready for the wig

1. Take a skin test.

Some women are allergic to the chemicals used to hold a wig in place.

A. First, apply a small amount of liquid adhesive or double-sided wig tape to the back of your hand.

B. Then keep the adhesive for at least 24 hours.

If the skin becomes red or itchy, purchase wig tape or hypoallergenic adhesive to use instead.

If the skin is not affected, you can safely wear the wig.

2. Flatten your hair.

The flatter your hair is on your head, the more beautiful the wig will be.

You can braid the short hair into cornrows or secure it against your head using gel and bobby pins.

For long hair, tie your hair back into a low ponytail first.

Then wrap the ponytail in a flat bun and secure it with bobby pins.

Let the gel or hairspray dry before continuing.

Expert tip:

If you have a lot of hair, make two French braids and wrap them tightly against your head.

3. Put a stocking on your head.

The wig caps are soft cups that help flatten the hair and the wig to stay in place.

A.   Gently pull on the bottom cup, being careful not to disturb your flattened hair.

B. Adjust the cap so that it barely covers your hairline.

– If you have little or no hair, skip this step. Otherwise, the beanie will slip over your head and crumple under your wig.

– Make sure that all of your hair is tucked in this cup, even the hair at the back of the neck.

4. Prepare your skin

A.  Wash your skin with a mild cleanser and dry it with a towel.

B. Then dab a little 90 ° alcohol on a cotton ball and wipe it along the hairline. This will help remove excess sebum on your skin.

Putting on the wig

1. Test the fit of the wig.

A.  Before applying adhesives, you need to make sure the wig fits properly.

To do this, place the wig on your head and line it up with the natural line of your hair.

B. If the wig has tightening straps on the inside, you may need to adjust them to get a snug fit.

C. If the wig does not fit and does not have to tighten straps, contact the manufacturer for assistance.

– If you have a feeling of pressure around your scalp, the wig is too tight. Slightly loosen the straps.

– If the wig slips when you move your head, it is too loose. Tighten the straps.

2. Cut the lace.

A.   After your wig is properly fitted, you need to cut the lace. Use a few tweezers to pull the hair away from your face.

B. Next, using waving scissors, cut the lace along the natural hairline.

C. You should leave about 3mm of lace. This should only be done the first time you wear the wig.

– Some wigs do not need to be trimmed before wearing. These wigs have little to no excess lace.

– You can buy pleating scissors at sewing supply stores.

3. Remove the wig and set it aside.

A.  Carefully remove the wig, leaving all clips in place, and lay it on a clean, flat surface.

B. Arrange the wig so that it is easy to see which part goes to the hairline and which part goes to the nape of the neck.

– If you need to loosen any fasteners to remove the wig, your wig is too tight.

4. Apply wig tape.

A.  Cut 6-10 small pieces of wig tape.

B. Next, line up your hairline with small pieces of tape, pressing the sticky side against your skin.

Use a mirror during the operation to create an even hairline.

C. Once the tape is applied, remove the heavy foam padding to reveal the other side of the tape.

– Make sure all the pieces are touching. Otherwise, you risk having holes in the hairline.

– Wig tape can be purchased at wig stores or online.

5. Use liquid adhesive.

A.  If you don’t want to use wig tape, you can use liquid lace adhesive instead.

B. Use a clean makeup brush to apply the adhesive in a thin line down the length of your hair.

Depending on the type of adhesive, you may need to wait a few minutes before wearing your wig.

– If you are using a soft adhesive, allow the glue to dry long enough for it to become tacky before applying the wig.

– If you use hard adhesive, you can apply the wig immediately.

6. Apply the wig.

A.  Gently pull on the wig. First, adjust the edge of the wig so that the hair matches.

B. Next, adjust the back of the wig so that it hangs naturally over your hair.

C. Finally, press the lace of the wig into your adhesive or wig tape.

– After you squeeze the lace into the adhesive or wig tape, it is very difficult to remove.

Make sure the wig is perfectly aligned before doing this.

Why Luvmehair? Luvmehair provides the highest quality hair products in the industry while guaranteeing professional and informed expert assistance for a pampering online shopping experience.”

RELATED ARTICLES

Leave a Reply

Your email address will not be published. Required fields are marked *